Ngày nhận bài: 22-12-2020
Ngày duyệt đăng: 02-03-2023
DOI:
Lượt xem
Download
Cách trích dẫn:
EFFECTS OF THE MAIN OPERATING PARAMETERS ON SEED HOLDINGIN A SEEDER-PNEUMATIC METERING DEVICE WITH AN INCLINED PLATE FOR MAIZE
,
Nguyen Chung Thong
1
Từ khóa
Seeder-pneumatic metering device, maize sowing machine, pneumatic metering device with inclined disc
Tóm tắt
Today's pneumatic sowing machines often use a seeder-pneumatic metering device with vertical seed discs. The weakness of a seeder-pneumatic metering device with a vertical disc is its low efficiency in receiving and holding seeds. In order to improve the suction and retention of seeds during sowing, the seed disc in a metering device was placed tilted compared to the vertical direction (pneumatic metering device with an inclined disc). The study was carried out according to the single-factor experimental method to determine the main working parameters of the aerodynamic sowing unit combined with the inclined disc.The results showed that an inclined seed disc is more effective than a vertical one in receiving and holding seeds during the sowing process. Specifically, the research focused on determining the effects of the main parameters - suction pressure, seed hole diameter, seed hole velocity, and angle of the seed disc - on the ability of the metering device to receive and hold seeds. The experimental results showed that an effective maize pneumatic metering device with an inclined disc has the following working parameters: 50-100mmHg vacuum pressure; 4-5.5mm seed hole diameter; a seeding hole velocity of less than 0.68 m/s; and the seed disc angled at 20-35degrees from the vertical direction.
Tài liệu tham khảo
Arzu Y. & Adnan D. (2007). Optimization of the seed spacing uniformity performance of a vacuum type precision seeder using response surface methodology. Biosys. Engg. 97: 347-356.
Ismett O., Adnan D. & Arzu Y. (2012). An evaluation of seed spacing accuracy of a vacuum type precision metering unit based on theoretical considerations and experiments. Turkey J. Agric. and For. 36: 133-144.
Karayel D., Barut Z.B. & Ozmerzi A. (2004). Mathematical modeling of vacuum pressure on a precision seeder. Biosys. Engg. 87(4): 437-444.
Satti H.Y., Qingxi L., Jiajia Y. & Dali H. (2012). Design and test of a pneumatic precision metering device for wheat. Agril. Engg. Int. CIGR J. 14(1): 16-25.
Singh R.C., Singh G. & Saraswat D.C. (2005). Optimization of design and operational parameters of a pneumatic seed metering device for planting cotton seeds. Biosys. Engg. 92(4): 429-438.
Yasir H.S., Qingxi L., Jiajia Y. & Dali H. (2013). Dynamic analysis for kernel picking up and transporting on a pneumatic precision metering device for wheat. Agril. Engg. Int. CIGR J. 15(2): 95-100.
Yu J., Liao Y., Cong J., Yang S. & Liao Q. (2014). Simulation analysis and match experiment on negative and positive pressure of pneumatic precision metering device for rapeseed. Int. J. Agric. Biol. Engg. 7(3): 1-12.
Zeliha B.B. & Aziz O. (2004). Effect of different operating parameters on seed holding in the single seed metering unit of a pneumatic planter. Turkey J. Agric. Forestry. 28: 435-441.
Zhao Z., Li Y., Chen J. & Xu L. (2010). Numerical analysis and laboratory testing of seed spacing uniformity performance for vacuum cylinder precision seeder. Biosys. Engg.106: 344-351.